Samsung SV-651B Manual de servicio Pagina 53
- Pagina / 226
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
GE HEALTHCARE
D
IRECTION 5194296-100, REVISION 10 LOGIQ BOOK XP SERIES BASIC SERVICE MANUAL
Chapter 2 Pre Installation 2-7
2-3-2 Required Features
NOTE: GE Medical Systems requires a dedicated power and ground for the proper operation of its
Ultrasound equipment. This dedicated power shall originate at the last distribution panel before
the system.
Sites with a mains power system with defined Neutral and Live:
The dedicated line shall consist of one phase, a neutral (not shared with any other circuit), and a full
size ground wire from the distribution panel to the Ultrasound outlet.
Sites with a mains power system without a defined Neutral:
The dedicated line shall consist of one phase (two lines), not shared with any other circuit, and a full
size ground wire from the distribution panel to the Ultrasound outlet.
Please note that image artifacts can occur, if at any time within the facility, the ground from the main
facility's incoming power source to the Ultrasound unit is only a conduit.
• Dedicated single branch power outlet of adequate amperage meeting all local and national codes
which is located less than 2.5 m (8 ft.) from the unit’s proposed location
• Door opening is at least 76 cm (30 in) wide
• Proposed location for unit is at least 0.2m (0.67 ft.) from the wall for cooling
• Power outlet and place for any external peripheral are within 2 m (6.5 ft.) of each other with
peripheral within 1 m of the unit to connect cables.
• Power outlets for other medical equipment and gel warmer
• Power outlets for test equipment and modem within 1 m (3.2 ft.) of unit
• Clean and protected space to store transducers (in their cases or on a rack)
• Material to safely clean probes (done with a plastic container, never metal)
2-3-3 Desirable Features
• Door is at least 92 cm (3 ft.) wide
• Circuit breaker for dedicated power outlet is easily accessible
• Sink with hot and cold water
• Receptacle for bio–hazardous waste, like used probe sheaths
• Emergency oxygen supply
• Storage for linens and equipment
• Nearby waiting room, lavatory, and dressing room
• Dual level lighting (bright and dim)
• Lockable cabinet ordered by GE for its software and proprietary manuals.
- LOGIQ BOOK XP Series 1
- Important Precautions 3
- ΠΡΟΕΙΔΟΠΟΙΗΣΗ 5
- GE HEALTHCARE 10
- WARNINGWARNING 12
- LEGAL NOTES 13
- Revision History 14
- List of Effected Pages(LOEP) 14
- Table of Contents 15
- CHAPTER 2 16
- Pre Installation 16
- CHAPTER 3 17
- Installation 17
- 4 Table of Contents 18
- CHAPTER 4 19
- 6 Table of Contents 20
- CHAPTER 5 21
- CHAPTER 6 22
- CHAPTER 7 23
- 10 Table of Contents 24
- CHAPTER 8 25
- CHAPTER 9 26
- CHAPTER 10 27
- 14 Table of Contents 28
- Chapter 1 29
- Introduction 29
- Section 1-2 31
- Important Conventions 31
- 1-2-2 Standard Hazard Icons 32
- 1-2-3 Product Icons 33
- Table 1-4 Warnings 34
- Chapter 1 Introduction 1-7 35
- Section 1-3 37
- Safety Considerations 37
- 1-3-4 Electrical Safety 38
- 1-3-5 Labels Locations 38
- 1-3-6 Battery Safety 39
- AND ADJUSTING 40
- Section 1-4 43
- EMC, EMI, and ESD 43
- Section 1-5 44
- Customer Assistance 44
- 1-5-2 System Manufacturer 45
- Chapter 2 47
- Section 2-2 48
- General Console Requirements 48
- Inrush Current 49
- 100V 0.38A 0.41A 49
- 240V 0.20A 0.21A 49
- 2-2-3 EMI Limitations 50
- Section 2-3 52
- Facility Needs 52
- 2-3-2 Required Features 53
- 2-3-3 Desirable Features 53
- EXAM INAT IO N 54
- Chapter 3 57
- 3-1-3 Installation Warnings 58
- 3-1-4 Safety Reminders 59
- THE UNIT! 59
- Section 3-2 60
- Interleaver 62
- Plastic bag 62
- Section 3-3 63
- Packing the Equipment 63
- Section 3-4 64
- Preparing for Installation 64
- Section 3-5 65
- Completing the Installation 65
- 3-5-2 Power Off/ Shutdown 66
- 3-5-3 Transducer Connection 67
- Section 3-6 68
- System Configuration 68
- 3-6-3 Approved peripherals 69
- 3-6-4 Connecting Cables 70
- Pin No. Signal Pin No. Signal 72
- Chapter 3 Installation 3-21 77
- Footswitch FSU 2001 78
- Footswitch FSU 1000 78
- 3-6-6 Available Probes 80
- Section 3-7 81
- Software/Option Configuration 81
- Section 3-8 82
- Section 3-9 83
- Loading the System Software 83
- 3-9-4 Functional Check-out 99
- 3-9-5 Option Key Update 100
- EALTHCARE 101
- 3-9-6 Probe Recognition Check 104
- Section 3-10 106
- Paperwork 106
- Chapter 4 107
- Functional Checks 107
- Section 4-3 108
- General Procedure 108
- 4-3-2 Power Off/ Shutdown 109
- 4-3-6 System Features 113
- 4-3-7 B Mode Checks 116
- Step Task Expected Result(s) 117
- 4-3-7-3 B Mode Softmenu Key 118
- 4-3-8 M Mode Controls 119
- 4-3-9 Color Flow Mode Checks 122
- 4-3-10 Doppler Mode Checks 125
- 4-3-11 Basic Measurements 128
- 4-3-12 Probe/Connectors Usage 129
- 4-3-13 Using Cine 130
- 4-3-14 Image Management (QG) 130
- Section 4-4 136
- Software Configuration Checks 136
- Section 4-5 136
- Peripheral Checks 136
- Chapter 5 137
- Section 5-2 138
- Block Diagrams and Theory 138
- 5-2-2 General Information 139
- Section 5-3 140
- Power Diagrams 140
- 5-3-3 Air Flow Distribution 141
- 5-3-4 Fans 142
- Section 5-4 143
- Common Service Platform 143
- 5-4-3 Service Home Page 145
- 5-4-5 Diagnostics 150
- FIELD IS NOT YET POPULATED 151
- FIELD IS NOT YE POPULATED 151
- Chapter 6 155
- Service Adjustments 155
- Section 6-2 156
- Monitor Adjustments 156
- Chapter 7 157
- Diagnostics/Troubleshooting 157
- Section 7-2 158
- Gathering Trouble Data 158
- Section 7-3 160
- Screen Captures 160
- 7-3-3 Capturing a Screen 162
- Section 7-4 164
- 7-4-3 Reset Database 167
- 7-4-3 Reset Database (cont’d) 168
- 7-4-4 Clean Userdefs 169
- 7-4-4 Clean Userdefs (cont’d) 170
- 7-4-5 Update FPGA 171
- 7-4-6 Control Frame 171
- Section 7-5 173
- Common Diagnostics 173
- Section 7-6 175
- 7-6-2 FRU Test 176
- N/A 40001 179
- Chapter 8 181
- Replacement Procedures 181
- Section 8-3 184
- Trackball Roller Cleaning 184
- Chapter 9 187
- Renewal Parts 187
- Section 9-5Keyboard Assy 190
- Section 9-6Bottom Assy 190
- Chapter 9 Renewal Parts 9-9 195
- Chapter 9 Renewal Parts 9-11 197
- Chapter 9 Renewal Parts 9-13 199
- Section 9-10Manuals 201
- Section 9-11Probes 202
- Chapter 10 203
- Care & Maintenance 203
- Section 10-2 204
- Why do Maintenance 204
- Section 10-3 204
- Maintenance Task Schedule 204
- Per Facilities 205
- QA Program Notes 205
- Section 10-4 206
- Tools Required 206
- Section 10-5 207
- System Maintenance 207
- ÷ Step Description 208
- 10-5-3 Input Power 209
- 10-5-4 Cleaning 209
- 10-5-5 Physical Inspection 210
- 10-5-7 Probe Maintenance 211
- Section 10-6 213
- Electrical Safety Tests 213
- Section 10-7 220
- ELECTRICAL SAFETY 222
- 9900 Innovation Drive 226
- Wawautosa, Wisconsin 53226 226
Relacionado con productos y manuales para De medición, control y control Samsung SV-651B
(76 paginas)
(291 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.085 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales