Samsung ML-1610 - B/W Laser Printer Especificaciones Pagina 68
- Pagina / 131
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Disassembly and Reassembly
Samsung Electronics
Service Manual
5-7
5.2.7 RX Drive
1.Before Disassembling
-Separate the font cover.(Refer to 5.2)
-Separate the SMPS cover.(Refer to 5.3)
-Separate the Main cover.(Refer to 5.4)
2.Release 2 screws (Screw x 2:Silver_M3,6001-
000130)connected to the engine shield and 6 screws
(Screw x 6:Gold_M3,6003-000296)connected to the
frame. Separate the RX drive by pulling it out toward
the arrow direction.
3.Remove the connector from the separated RX drive. 4.After removing the RX drive,RDCN Gear, OPC Gear,
Fuser Gear, and Feed Gear can be removed from
the frame.
RX Drive
RDCN Gear
OPC Gear
Fuser Gear
Feed Gear
Please, be careful not to touch the protruding 4 screws at the
outside of the RX drive.
Note:
- LASER PRINTER 1
- Contents 2
- Continued 3
- 1. Precautions 5
- 1.2 Safety Caution 6
- 1.2.3 Handling Precautions 7
- 1.3 ESD Precautions 8
- 2. Product Specifications 9
- 2.2.2 Controller 10
- 2.2.4 Environmental Range 11
- 2.2.5 Toner Cartridge 11
- 2.2.6.1 Input Paper Size 12
- 2.2.6.2 Input capacity 12
- 2.2.6.3 Output capacity 12
- 2.3 Model Comparison Table 13
- Product Specifications 14
- 3. System Overview 15
- Unit Layout 16
- 3.1.1 Feeding 17
- 3.1.2 Transfer Ass’y 17
- 3.1.3 Driver Ass’y 17
- 3.1.4 FUSER 17
- System Overview 18
- 3.1.6 Toner Cartridge 20
- 3.2.1 H/W Overview 21
- 3.2.1.3 Flash Memory 22
- 3.2.1.4 DRAM 22
- 3.2.2 Main Board 23
- 3.2.3.1 Introduction 25
- 3.2.4 Sensor Controller 28
- Pin Signal 29
- 3.3.1 Introduction 34
- - F/W Architecture 37
- 3.3.6 LED Behaviors 38
- 3.3.7 Error LED Operation 38
- 3.4.1 Accessory List 39
- 3.4.3 Loading Paper 42
- 3.4.5 Turning the Printer on 44
- 3.4.6 Printing a Demo Page 44
- 4. Alignment and Adjustments 46
- 4.2 Control Panel 47
- 4.2.3 Cancel button 48
- Alignment and Adjustments 49
- 4.5 Periodic Defective Image 50
- 4.6 How to use DCU 51
- 4.6.2 Code 52
- 4.6.3 Self Diagnostic Mode 53
- 4.6.4 Self Test Button 55
- 4.7 Paper Path 56
- 4.7.1 Clearing Paper Jams 57
- 4.7.2 In the Paper Exit Area 57
- 4.7.3 In the Paper Feed Area 59
- 5. Disassembly and Reassembly 62
- 5.2.1 Front Cover 63
- 5.2.2 Cassette Tray 63
- 5.2.3 SMPS Cover 64
- 5.2.4 Main Cover 64
- Jam Cover 65
- Main Cover 65
- 5.2.5 Top Cover 66
- 5.2.6 HVPS 67
- 5.2.7 RX Drive 68
- 5.2.8 Fuser 69
- Fuser Dummy Cover 70
- Lamp Cover_R 70
- Lamp Cover_L 70
- Thermostat 71
- Thermistor 71
- Disassembly and Reassembly 72
- Engine Shield 73
- (W/Main PBA, SMPS) 73
- Actuator Feed Sensor Lever 73
- Main PBA 73
- 5.2.10 LSU 74
- 5.2.11 Paper Path Frame 74
- 5.2.12 Pick_Up Roller 75
- 6. Troubleshooting 76
- 6.1.1 Basic Check List 77
- 6.1.2 Initial Inspection 78
- 6.2 Bad discharge 79
- 6.2.3 JAM 1 80
- 6.2.4 JAM 2 80
- 6.2.5 Multi-Feeding 81
- Troubleshooting 82
- 6.3 Malfunction 83
- 6.3.4 Paper Empty 84
- 6.3.6 Cover Open 85
- 6.3.9 No Power 86
- 6.4 Bad Software Environment 88
- 6.4.3 Abnormal Printing 90
- 6.4.4 SPOOL Error 91
- 6.5 Bad image 92
- 6.5.3 Horizontal Black Band 93
- 6.5.4 Black/White Spot 93
- 6.5.5 Light Image 94
- 6.5.6 Dark Image or a Black 94
- 6.5.7 Uneven Density 95
- 6.5.8 Background 95
- 6.5.9 Ghost (1) 96
- 6.5.10 Ghost (2) 96
- 6.5.11 Ghost (3) 97
- 6.5.12 Ghost (4) 97
- 7.1 Main Assembly 100
- Main Assembly Parts List 101
- 7.2 Frame Assembly 102
- Frame Assembly Parts List 103
- 7.3 Fuser Unit 104
- Fuser Unit Parts List 105
- 7.4 Paper Path Unit 106
- Paper path Unit Parts List 107
- 8. Block Diagram 108
- 8.2 System Timing Chart 109
- 9. Connection Diagram 110
- 10. Schematic Diagrams 111
- Main Board(2/4) 112
- Main Board(3/4) 113
- Main Board(4/4) 114
- Service Manual 115
- Schematic Diagram) 115
- Samsung Electronics 115
- 10-3 SMPS Circuit Diagram 116
- Schematic Diagram 117
- HVPS Circuit Diagram(2/3) 118
- • DVM(Digital Volt Meter) 120
- Acronyms and Abbreviations(2) 122
- Reference Information 123
- 11.4 Sample Tests Patterns 124
- 12. Circuit Description 125
- Circuit Description 126
- 12.1.2 PWM Controller 127
- 12.1.3 Motor Driver 128
- 12.1.4 LSU Controller 128
- 12.1.5 ADC Controller 130
- Printed in Korea 131
Relacionado con productos y manuales para Software Samsung ML-1610 - B/W Laser Printer
Software Samsung SC-MX20ER Manual de usuario
(49 paginas)
(49 paginas)
Software Samsung 510N Manual de usuario
(50 paginas)
(50 paginas)
Software Samsung PC680-ZA Manual de servicio
(390 paginas)
(390 paginas)
Software Samsung SCX-4725FN Manual de usuario
(120 paginas)
(120 paginas)
Software Samsung ML-2550 Manual de usuario
(235 paginas)
(235 paginas)
Software Samsung SV-M10K Guía de usuario
(62 paginas)
(62 paginas)
Software Samsung SCX-6545N Series Guía de usuario
(180 paginas)
(180 paginas)
Software Samsung CLP-550N Manual de usuario
(48 paginas)
(48 paginas)
Software Samsung SCX-6322DN Manual de usuario
(6 paginas)
(6 paginas)
Software Samsung SCX-5530FN Manual de usuario
(6 paginas)
(6 paginas)
Software Samsung CLX-8380ND Manual de usuario
(6 paginas)
(6 paginas)
Software Samsung MFP SCX-6345N Guía de usuario
(28 paginas)
(28 paginas)
Software Samsung MAX-DB9900 Manual de usuario
(38 paginas)
(38 paginas)
Software Samsung SF-5100P Guía de usuario
(156 paginas)
(156 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.071 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales